A person holds a black diy digital rangefinder camera to their face, with shelves of camera gear behind.

Two Canon Donor Cameras Yield a DIY Digital Rangefinder Built in Weeks

User avatar placeholder
Written by Seth Sebastian

2026-11-22

Mr. 50mm is back with a second homemade diy digital rangefinder camera, and this one has a bigger sensor. The earlier build combined parts from a FED 5 Soviet-era rangefinder with a Panasonic GF3 Micro Four Thirds camera. The new model moves to APS-C.

The first camera, which Mr. 50mm called the “RGM-79,” used a Micro Four Thirds sensor. The new “C7M” uses an APS-C sensor, which is physically larger. Mr. 50mm based its imaging pipeline on the original Canon EOS M mirrorless camera, released in 2012.

A homemade RGM-79 rangefinder camera built earlier this year by Mr. 50mm.
The RGM-79 that Mr. 50mm built earlier this year.

The EOS M carries an 18-megapixel APS-C CMOS sensor. The GF3 sensor it replaces measured 12.1 megapixels. That is a meaningful jump in resolution for a camera built from salvaged parts.

A diy digital rangefinder camera needs two donor cameras. This time, Mr. 50mm kept the rangefinder side in the Canon family. The donor body is the Canon 7, part of a rangefinder camera series that ran from 1961 to 1967. It began with the original Canon 7 and ended with the Canon 7sZ.

Camera bodies can be customized in smaller ways too. Offbit’s E-Paper Lens Chart for Camera Bodies offers a cheap, practical tweak worth a look.

A Canon 7 rangefinder camera, one of two donor bodies used in the build.
One of the two donor cameras, the Canon 7 rangefinder.

The unfinished C7M already shows promise as a diy digital rangefinder camera. Mr. 50mm has not yet released a build video, and the project is still in progress. He singles out the Canon 7 viewfinder as a clear improvement over the FED he used before.

“The bar wasn’t that high, but the Canon 7 does a lot of things very, very well,” Mr. 50mm says. “You get a brighter finder, you get projected and selectable frame lines, and they’re parallax-corrected.”

The Canon 7 also uses a Leica M39 screw mount. That mount has a large selection of lenses on the market, a practical advantage for a camera built around lens choice.

The Canon 7 has few physical controls. Mr. 50mm treats that as a benefit, since fewer controls mean fewer to transfer or work around.

“It doesn’t have that many dedicated controls, which helps reduce the amount of controls I need to either port or figure out if I’m okay to live without,” he says. “In the end, the digital camera really just has to be able to do two things. It has to accommodate the rangefinder that I’m gonna put on top, and it has to be able to accommodate the mount that I’m using.”

The conversion was not simple. Mr. 50mm said the EOS M could not simply be taken apart and fitted with new parts.

Hacking existing hardware into something new is a recurring theme in DIY tech. Natasha Dzurny’s Puppet Turned Cyberdeck Computer shows how far that idea can be pushed.

“Unfortunately, it isn’t just as easy as disassembling an EOS M and then jamming on new parts,” he says. “There [were] quite a few modifications that needed to be done to the camera to make this work, which I’ll discuss probably in depth in another video.”

Disassembled camera parts, a circuit board, a lens mount, and a screen lie on blue silicone mat.
Disassembled camera components, including a circuit board, 3D-printed parts, a lens mount, and a display screen, are laid out on a blue silicone mat.

Mr. 50mm solved the largest problems, according to the project video. He describes the C7M as “mostly done.” The full build took only a couple of weeks from start to finish, even after a damaging drop during construction.

Some issues remain. Rangefinder calibration is not finished, and several components do not line up perfectly. Mr. 50mm plans to trim more material from the EOS M’s parts, though he is not sure how much material is left to remove.

He has also promised a guide. “Eventually, once things get a bit more ironed out, I’ll draft up a tutorial on how you can actually make your own,” he says.

What a diy digital rangefinder camera could cost

Digital rangefinders are expensive, and donor parts plus 3D-printed components offer a cheaper route. The method still requires comfort with a demanding build process.

The cost comparison is straightforward. A used Canon EOS M body sells for around $260, which is not much more than a Canon 7 rangefinder body. Printing the remaining parts on a 3D printer adds little cost. A new Leica digital rangefinder costs far more.

The C7M is not finished, but it shows what a diy digital rangefinder camera build can achieve. Mr. 50mm’s YouTube channel is the place to follow the project’s next steps, including the calibration work and the promised tutorial.

A person holds a black diy digital rangefinder camera to their face, with shelves of camera gear behind.
A person holds a black, 3D-printed-style camera with a Canon Lens 50mm 1:1.4 lens in front of their face, with shelves of camera gear in the background.

Via petapixel.com

Frequently asked questions

What sensor does the C7M diy digital rangefinder use?

The C7M uses an APS-C sensor, which is physically larger than the Micro Four Thirds sensor in the first camera, the RGM-79. The EOS M sensor it draws on carries 18 megapixels, compared with 12.1 megapixels in the Panasonic GF3 sensor it replaces.

Which donor cameras were used to build the C7M?

The C7M was built from two donor cameras: the original Canon EOS M mirrorless camera, which supplied the imaging pipeline and sensor, and the Canon 7 rangefinder body, which provided the rangefinder side.

What lens mount does the Canon 7 rangefinder use?

The Canon 7 uses a Leica M39 screw mount. The article notes that this mount has a large selection of lenses on the market, which is a practical advantage for a camera built around lens choice.

How long did it take to build the C7M digital rangefinder?

The full build took only a couple of weeks from start to finish, even after a damaging drop during construction. The creator describes the camera as mostly done, though rangefinder calibration is not finished.

Menu