Wireless controller receivers rarely get a second act. EasySMX’s X20 Pro gives its receiver one. Seat the receiver in the included easysmx x20 pro stand, and the stand turns into a magnetic charging dock. The same small part that links the pad to your PC also keeps its battery topped up.
Unlike a basic wireless controller stand, this controller charging dock holds the controller at an angle on two low feet, with the receiver resting between the grips. Contacts on the back line up with magnets, so setting the pad down also connects it to power. A cable runs to the dock and can stay plugged in, which spares you from connecting the controller itself every night.
If keeping your gear powered is the appeal here, Peak Design’s 5,000mAh Wireless Battery Charger takes a similar minimalist approach to keeping devices topped up.

Lift the receiver off the stand and it works as a standalone dongle. It plugs straight into a PC, or it can sit at the end of a USB cable when the computer lives under a desk. It also attaches to the controller for travel, which is easier than packing the whole dock for a weekend away. The controller can still charge directly over USB-C.

The thumbstick rings are the more unusual feature. Each ridged ring changes how much force a push requires. A looser left stick suits quick movement, while a firmer right stick gives you finer control over the camera. The sticks read position with tunneling magnetoresistance (TMR), a magnetic sensing method, so the rings adjust resistance rather than the sensing itself.

The triggers operate in two modes. In analog mode, a Hall effect sensor, a chip that measures magnetic field strength to judge how far a trigger has moved, reads partial pulls. That precision helps when you need to ease onto the throttle coming out of a corner. Switches on the back change the triggers to a short, digital click for single inputs. Four vibration motors are split between the triggers and the grips.

Six programmable buttons sit alongside the standard ABXY face buttons. Two small shoulder buttons are included, and four more are on the back, two of which are removable paddles. Mapping jump to a rear paddle lets your thumb stay on the camera stick. If the broad, faceted D-pad doesn’t suit you, a traditional cross is available as a swap.

Tinkerers who enjoy repurposing hardware for play may also like turning an old Galaxy S10 into a rugged cyberdeck, a budget project built around a retired phone.

A small display above the sticks shows the battery level and the active connection. You can change settings such as vibration from that screen, without installing software on a computer. It is a practical touch for a controller that already asks you to think about where its receiver lives.

Platforms and Pricing for the easysmx x20 pro stand
The X20 Pro works with Windows PCs, Nintendo Switch, Android devices, and iOS. Depending on the device, you can connect over Bluetooth, 2.4 GHz wireless, or wired USB-C. Xbox and PlayStation consoles fall outside its support list.
EasySMX lists the controller at $79.99 in the US, in gray or black. The raised screen and narrow RGB accents make it look like a gaming accessory, but the stand is the real story. It gives the easy-to-lose receiver a fixed home, and it keeps the controller charged until you pick it up.



H/T yankodesign.com
Frequently asked questions
Which platforms does the EasySMX X20 Pro support?
The X20 Pro works with Windows PCs, Nintendo Switch, Android devices, and iOS. Depending on the device, you can connect over Bluetooth, 2.4 GHz wireless, or wired USB-C. Xbox and PlayStation consoles are not on its support list.
How much does the EasySMX X20 Pro controller cost?
EasySMX lists the X20 Pro controller at $79.99 in the US. It is available in gray or black.
How does the EasySMX X20 Pro stand charge the controller?
The receiver seats in the stand, which then acts as a magnetic charging dock. Contacts on the controller’s back line up with magnets, so setting the pad down connects it to power. The stand’s cable can stay plugged in, so you don’t have to connect the controller itself each night.
Can the X20 Pro receiver be used without the stand?
Yes, the receiver works as a standalone dongle once lifted off the stand. It can plug straight into a PC or sit at the end of a USB cable, and it can attach to the controller for travel.
More in






